Rick's Free Auto Repair Advice » Equinox

Intermittent problems on GM vehicles

Rick — Thu, 08 Sep 2011 21:23:07 +0000

GM vehicles from the mid ’90′s to the present are known for faulty ignition switches. The problems are almost always intermittent. Intermittent starting, dying while driving, A/C to start blowing warm air or for the blower fan to stop (depending on which GM model we’re talking about), along with an ABS light. In fact, any time you see erratic or intermittent problems that could be electtrical in nature on a GM vehicle, you should immediately suspect the ignition switch. Always test the igntion switch during an intermittent problem to see if the switch is providing power (use a meter).Or, wiggle the wires going to the switch. GM techs replace so many of these that it’s almost automatic for them to head there first

In the case of the A/C the problem is usually the ignition switch heating up and not providing power to the A/C clutch and the ABS computer. If you want to diagnose the problem, buy a wiring diagram for your vehicle form eautorepair.net or alldata.com (there are way to many GM models to list their wiring diagrams here) and test for power at the switched terminals when the problem happens. Or, just replace the ignition switch.

For more information on this repair or any others for your vehicle, buy an online subscription to either Alldatadiy.com or eautorepair.net. Click on this link to compare the two services: Compare Alldata and Eautorepair.

If you just need information for a single repair and want to save money,eautorepair offers a lower price 1-week subscription for only $11.99. Or, if you’ll be working on this vehicle in the future, you can buy a 1-year subscription (Alldatadiy.com for $26.99, or eautorepair.net $29.99)

Alldatadiy.com

eautorepair.net

Both Alldata and Eautorepair offer professional grade shop manuals at a price you can afford. Check them out!.

P0332, Circuit Low Input (Bank 2) on GM products

Rick — Tue, 06 Sep 2011 04:10:36 +0000

Also P0335 and P0340

If you think you should replace the knock sensor after getting this code, think again. This is a perfect example of where a sensor can be telling the truth and the root cause of the problem is somewhere else. Here’s the scoop. Most late model engine use variable valve timing to change the opening and closing timing of the valves. The device that actually changes the valve timing is called the cam phaser (yeah, like on Star Treck). Some cam phasers use oil pressure to rotate the camshaft slightly to change the timing. That’s great when it’s working well. But if you’ve changed your own oil and used a viscosity that’s different from the manufacturer’s recommendations, you can screw up the phaser. For example, some people don’t believe the manufacturer’s recommendation to use 5W-30. So they change their oil with 10W-30. The slightly thicker oil can cause the phaser to respond more slowly to computer commands. And when the cam is out of phase from the commanded position, you can get pre-ignition, or pinging. Yup, if you used this oil and now have this trouble code, point your finger right at yourself.

The same holds true if you think you can get away with not changing your oil on time. Think sludge buildup isn’t a problem? Well guess what, sludge in a cam phaser can also cause trouble codes.

If you’re getting these codes and think it might be caused by oil, change your oil and filter and drive the vehicle first. Perhaps the clean oil can clear out the passages.

Here are a few other things that can cause this trouble code:

Check the electrical connector on the cam phaser. If you see oily buildup, disconnect the connector and check inside. Oil can sometimes seep into the connector and that would give false readings.

Alldatadiy.com

eautorepair.net

Both Alldata and Eautorepair offer professional grade shop manuals at a price you can afford. Check them out!.

A/C doesn’t work and ABS light on

Rick — Thu, 01 Sep 2011 17:53:39 +0000

GM vehicles are known for faulty ignition switches. The problems are almost always intermittent. One common symptom is for the A/C to start blowing warm air or for the blower fan to stop (depending on which GM model we’re talking about), along with an ABS light. The problem is usually the ignition switch heating up and not providing power to the A/C clutch and the ABS computer. If you want to diagnose the problem, buy a wiring diagram for your vehicle form eautorepair.net or alldata.com (there are way to many GM models to list their wiring diagrams here) and test for power at the switched terminals when the problem happens. Or, just replace the ignition switch.

Alldatadiy.com

eautorepair.net

Both Alldata and Eautorepair offer professional grade shop manuals at a price you can afford. Check them out!.

Performance Chip? GM Revokes Warranty on Chipped Vehicles

Rick — Fri, 18 Dec 2009 23:16:46 +0000

GM issued a technical service bulleting (TSB) #09-06-04—026 regarding revocation of warranty coverage on any GM vehicle in which the factory calibrations (software) has been removed or altered. The TSB applies to ALL GM gasoline passenger cars and trucks from 2006- present.

It’s important to note that GM is seeing enough damaged engines and transmissions to make this announcement. Here’s a direct quote from the TSB:

“When alteration to the GM-released engine or transmission control calibrations occurs, it subjects powertrain and driveline components (engine , transmission, transfer case, driveshaft and rear axle) to stresses that were not tested by General Motors. It is because of these unknown stresses, and the potential to alter reliability, durability and emissions performance, that GM has adopted a policy to cancel any remaining warranty coverage to the powertrain and driveline components whenever the presence of a non-GM (aftermarket) calibration is confirmed – even if the non-GM control module calibration is subsequently removed.”

The TSB goes on to instruct the dealers on how to determine if the factory calibrations have been altered or removed. So don’t think you change restore the factory programming and tear into the dealer when they refuse to cover your warranty claim. They CAN tell what you’ve done.

So, if you’re planning on “chipping” your vehicle (which I do NOT recommend), be aware that you’re on your own and that the likelihood of damage to the engine and transmission increases dramatically.

Also, remember this: engine design is always a compromise between power, responsiveness, emissions, and fuel economy. You cannot change one variable without changing all the others. So, while chipping may increase power in one range of operation, you will pay for it in other areas. There’s no free lunch, despite what the chipmakers want you to believe.

Alldatadiy.com

eautorepair.net

Both Alldata and Eautorepair offer professional grade shop manuals at a price you can afford. Check them out!.

Hover your mouse over the REPAIR ARTICLES tab at the top of the page. The click on DIAGNOSTICS to search by SYMPTOM, TROUBLE CODE, or read TECH TIPS on how to diagnose a problem

Click on MAKE an MODEL to see all the articles I’ve written for your vehicle
Click on REPAIR TOPICS to read individual articles written for specific automotive systems

If you’ve had your car scanned and know the trouble code go to TROUBLE CODES

Here are some quick links to speed up your research

Click on the link below for speedy navigation:

ABS issues, how to bleed ABS brakes

Airbag issues or SRS light on

Alternator issues or how to test

Belt diagram or serpentine belt issues

Blower motor

Blower motor resistor

Brakes, brake issues, what kind of brake parts to buy, ABS issues

Car Alarms or Antitheft systems

Cooling system, Water pump, What type of coolant to use

Engine flush

Firing order, cylinder layout, finding #1 cylinder

MAF or MAP sensor

Oxygen sensors, How they work, How to change, How to test

PassLock or Passkey

Thermostat issues

Transmission flush

Serpentine belt diagrams

Window issues, power window motor, replace window regulator, glass adhesive

Headlights flicker on vehicle with daytime running lights

Rick — Sun, 06 Dec 2009 18:02:10 +0000

Every manufacturer has their share of problems with daytime running lights. Basically the system senses that the vehicle is running and the headlight switch is off. Programmed conclusion? Must be daylight, otherwise the driver would turn on the headlights. Other systems have light sensors. The Chrysler Daytime Running Light system gets screwed up by corrosion in the intelligent power module. Some GM vehicles fail due to a cracked Daytime Running Light resistor (computer provides power to the headlights, but runs it through a resistor to cut down on the headlamp brightness). Still another GM system runs the headlight commands through Daytime Running Lamp Module located behind the left side of the instrument panel. This module contains a diode that has a high failure rate. The module sends a command to the Daytime Running Lamps Relay located in the convenience center (firewall passenger side).

If you have the latter system, remove the relay and insert a jumper wire across the power terminals. See Relay Layout. If that fixes the problem, replace the relay. If it doesn’t, replace the Daytime Running Lamp Module.

Alldatadiy.com

eautorepair.net

Both Alldata and Eautorepair offer professional grade shop manuals at a price you can afford. Check them out!.

Hover your mouse over the REPAIR ARTICLES tab at the top of the page. The click on DIAGNOSTICS to search by SYMPTOM, TROUBLE CODE, or read TECH TIPS on how to diagnose a problem

Click on MAKE an MODEL to see all the articles I’ve written for your vehicle
Click on REPAIR TOPICS to read individual articles written for specific automotive systems

If you’ve had your car scanned and know the trouble code go to TROUBLE CODES

Here are some quick links to speed up your research

Click on the link below for speedy navigation:

ABS issues, how to bleed ABS brakes

Airbag issues or SRS light on

Alternator issues or how to test

Belt diagram or serpentine belt issues

Blower motor

Blower motor resistor

Brakes, brake issues, what kind of brake parts to buy, ABS issues

Car Alarms or Antitheft systems

Cooling system, Water pump, What type of coolant to use

Engine flush

Firing order, cylinder layout, finding #1 cylinder

MAF or MAP sensor

Oxygen sensors, How they work, How to change, How to test

PassLock or Passkey

Thermostat issues

Transmission flush

Serpentine belt diagrams

Window issues, power window motor, replace window regulator, glass adhesive

Daytime Running Lights Inoperative, DRL indicator flashes B2600

Rick — Sat, 17 Oct 2009 04:41:11 +0000

GM has issued a TSB #07-08-42-002A regarding troublesome daytime running lights. The symptoms are:

1) daytime running lights may not work at all
2) DRL indicator on instrument panel flashes and goes out
3) Trouble code B2600 comes up during code scan.

The TSB applies to 2005-06 Chevrolet Equinox, 2006 Pontiac Torrent, 2002-07 Saturn VUE

The cause of the problem is most likely a cracked DRL resistor. Follow this procedure to inspect and correct.

The parking brake must be released during this test procedure

Park the vehicle outside and shine a trouble light over the ambient sensor for 30 seconds.

Turn the headlight switch to the AUTO position
Press on the brake pedal
Turn the ignition key to the ON position
Shift the transmission out of PARK place into gear
Observe the DRL lamp on the instrument panel

If the DRL lamp stays on and both DRL lamps are on, the system is operating as designed

If the DRL flashes and goes out and only one DRL lamp flashes rapidly, the other DRL lamp may be burned out. Inspect the lamps and replace as needed

If the DRL flashes and goes out and NEITHER DRL lamp lights AND trouble code B2600 is stored in the computer, inspect the DRL resistor. The resistor is located on the left front bumper support.

To access the resistor on Chevrolet and Pontiac models, loosen the left front corner of the plastic wheel well liner where it attaches to the front fascia. Saturn vehicles do not require you to remove the front wheel or wheel well liner.

Clean the sensor and check for cracks or corrosion. IF the resistor is cracked or corroded, replace it. Install the new resistors, placing the washer between the resistor and the bumper support. Tighten the bolt to 53 IN/lbs. Do NOT exceed this torque or you may crack the new resistor.

Alldatadiy.com

eautorepair.net

Both Alldata and Eautorepair offer professional grade shop manuals at a price you can afford. Check them out!.

Hover your mouse over the REPAIR ARTICLES tab at the top of the page. The click on DIAGNOSTICS to search by SYMPTOM, TROUBLE CODE, or read TECH TIPS on how to diagnose a problem

Click on MAKE an MODEL to see all the articles I’ve written for your vehicle
Click on REPAIR TOPICS to read individual articles written for specific automotive systems

If you’ve had your car scanned and know the trouble code go to TROUBLE CODES

Here are some quick links to speed up your research

Click on the link below for speedy navigation:

ABS issues, how to bleed ABS brakes

Airbag issues or SRS light on

Alternator issues or how to test

Belt diagram or serpentine belt issues

Blower motor

Blower motor resistor

Brakes, brake issues, what kind of brake parts to buy, ABS issues

Car Alarms or Antitheft systems

Cooling system, Water pump, What type of coolant to use

Engine flush

Firing order, cylinder layout, finding #1 cylinder

MAF or MAP sensor

Oxygen sensors, How they work, How to change, How to test

PassLock or Passkey

Thermostat issues

Transmission flush

Serpentine belt diagrams

Window issues, power window motor, replace window regulator, glass adhesive

B1000, Airbag light on GM vehicles

Rick — Sat, 17 Oct 2009 04:23:08 +0000

GM has issued a TSB #08-09-004 to correct the false illumination of the airbag light and a corresponding B1000 trouble code. The TSB applies to 2008 Buick Enclave, 2005-08 Cadillac SRX, 2005-08 Chevrolet Equinox, 2007-08 GMC Acadia, 2006-08 Pontiac Torrent,
2007-08 Saturn OUTLOOK, and 2007-08 Suzuki XL-7.

These vehicles come equipped with a Passenger Presence System (PPS) to detect if a passenger is in the vehicle. The system communicates with the ECU and turns the passenger side airbag(s) on or off depending on passenger presences. This TSB requires a software update to correct the false illumination of the SRS light.

Alldatadiy.com

eautorepair.net

Both Alldata and Eautorepair offer professional grade shop manuals at a price you can afford. Check them out!.

Hover your mouse over the REPAIR ARTICLES tab at the top of the page. The click on DIAGNOSTICS to search by SYMPTOM, TROUBLE CODE, or read TECH TIPS on how to diagnose a problem

Click on MAKE an MODEL to see all the articles I’ve written for your vehicle
Click on REPAIR TOPICS to read individual articles written for specific automotive systems

If you’ve had your car scanned and know the trouble code go to TROUBLE CODES

Here are some quick links to speed up your research

Click on the link below for speedy navigation:

ABS issues, how to bleed ABS brakes

Airbag issues or SRS light on

Alternator issues or how to test

Belt diagram or serpentine belt issues

Blower motor

Blower motor resistor

Brakes, brake issues, what kind of brake parts to buy, ABS issues

Car Alarms or Antitheft systems

Cooling system, Water pump, What type of coolant to use

Engine flush

Firing order, cylinder layout, finding #1 cylinder

MAF or MAP sensor

Oxygen sensors, How they work, How to change, How to test

PassLock or Passkey

Thermostat issues

Transmission flush

Serpentine belt diagrams

Window issues, power window motor, replace window regulator, glass adhesive

ABS, Red Brake Light, Sevice Vehicle light, Trouble code U2100, cannot communicate with PCM or BCM – Chevrolet Equinox

Rick — Wed, 23 Sep 2009 17:09:26 +0000

If you run into this situation where you have these indicator lights and cannot communicate with the PCM or BCM, don’t freak out. You’ve run into this problem before-on your desktop computer. The multiple computers in your car have become confused and are locked into an endless loop called “logic lock.” To fix the problem, you have to “reboot” the computers.

Disconnect both positive and negative battery cables. Touch them together for 30 seconds to drain all capacitors in the system. Then reconnect the cables and start the vehicle. It may run different for the first 10 starts because you also wiped out the adaptive memory. But the computers will relearn the proper settings and you’ll be back in business within a few day’s driving.

Alldatadiy.com

eautorepair.net

Both Alldata and Eautorepair offer professional grade shop manuals at a price you can afford. Check them out!.

Hover your mouse over the REPAIR ARTICLES tab at the top of the page. The click on DIAGNOSTICS to search by SYMPTOM, TROUBLE CODE, or read TECH TIPS on how to diagnose a problem

Click on MAKE an MODEL to see all the articles I’ve written for your vehicle
Click on REPAIR TOPICS to read individual articles written for specific automotive systems

If you’ve had your car scanned and know the trouble code go to TROUBLE CODES

Here are some quick links to speed up your research

Click on the link below for speedy navigation:

ABS issues, how to bleed ABS brakes

Airbag issues or SRS light on

Alternator issues or how to test

Belt diagram or serpentine belt issues

Blower motor

Blower motor resistor

Brakes, brake issues, what kind of brake parts to buy, ABS issues

Car Alarms or Antitheft systems

Cooling system, Water pump, What type of coolant to use

Engine flush

Firing order, cylinder layout, finding #1 cylinder

MAF or MAP sensor

Oxygen sensors, How they work, How to change, How to test

PassLock or Passkey

Thermostat issues

Transmission flush

Serpentine belt diagrams

Window issues, power window motor, replace window regulator, glass adhesive

U codes – Chevrolet Equinox

Rick — Wed, 23 Sep 2009 17:03:17 +0000

U codes – Chevrolet Equinox

This vehicle is known for having data line problems. The data line carries digital data between different control modules. If a module shorts out, it can inject voltage onto the line which scrambles the digital data. The data line can also short to ground or break.

Data line issues are difficult to diagnose, so bring plenty of patience to your job.

Start with a factory wiring diagram (eautorepair.net). Next test the resistance across the 2 high speed data line wires at the diagnostic link connector (DLC). You should get a reading of 60 ohms. If you get a higher reading (120 ohms), disconnect one module at a time between the PCM and Body Control Module and jumper across the data line at that module. If resistance falls to the lower level and the vehicle operates properly, turn your attention to why that module may have failed. Check for proper power and ground to the module. .

Alldatadiy.com

eautorepair.net

Both Alldata and Eautorepair offer professional grade shop manuals at a price you can afford. Check them out!.

Hover your mouse over the REPAIR ARTICLES tab at the top of the page. The click on DIAGNOSTICS to search by SYMPTOM, TROUBLE CODE, or read TECH TIPS on how to diagnose a problem

Click on MAKE an MODEL to see all the articles I’ve written for your vehicle
Click on REPAIR TOPICS to read individual articles written for specific automotive systems

If you’ve had your car scanned and know the trouble code go to TROUBLE CODES

Here are some quick links to speed up your research

Click on the link below for speedy navigation:

ABS issues, how to bleed ABS brakes

Airbag issues or SRS light on

Alternator issues or how to test

Belt diagram or serpentine belt issues

Blower motor

Blower motor resistor

Brakes, brake issues, what kind of brake parts to buy, ABS issues

Car Alarms or Antitheft systems

Cooling system, Water pump, What type of coolant to use

Engine flush

Firing order, cylinder layout, finding #1 cylinder

MAF or MAP sensor

Oxygen sensors, How they work, How to change, How to test

PassLock or Passkey

Thermostat issues

Transmission flush

Serpentine belt diagrams

Window issues, power window motor, replace window regulator, glass adhesive

Clicking relays, Instrument Panel blinking – Chevrolet Equinox

Rick — Wed, 23 Sep 2009 16:37:58 +0000

Shops are reporting multiple electrical problems on these vehicles and most of them point to poor ground connections. In this case, you may experience any of these symptoms: instrument panel lights blinking, relays clicking, no power steering. You may also find these trouble codes:
U0001-High Speed CAN Communication Bus,
U0101-Lost Communication with TCM,
U0140-Lost Communication With Body Control Module,
U2107-Lost Communications with Body Control System,
U2105-CAN Bus Error ECM,
U2106-Lost Comm with Trans Control System

Start your diagnostics by checking all the fuses in the fuse panels. Next, disconnect and clean all ground cable connections. Pay particular attention to the ground cable from the negative battery terminal to the body.

Shops report that after cleaning all ground terminals, the problem goes away.

Alldatadiy.com

eautorepair.net

Both Alldata and Eautorepair offer professional grade shop manuals at a price you can afford. Check them out!.

Hover your mouse over the REPAIR ARTICLES tab at the top of the page. The click on DIAGNOSTICS to search by SYMPTOM, TROUBLE CODE, or read TECH TIPS on how to diagnose a problem

Click on MAKE an MODEL to see all the articles I’ve written for your vehicle
Click on REPAIR TOPICS to read individual articles written for specific automotive systems

If you’ve had your car scanned and know the trouble code go to TROUBLE CODES

Here are some quick links to speed up your research

Click on the link below for speedy navigation:

ABS issues, how to bleed ABS brakes

Airbag issues or SRS light on

Alternator issues or how to test

Belt diagram or serpentine belt issues

Blower motor

Blower motor resistor

Brakes, brake issues, what kind of brake parts to buy, ABS issues

Car Alarms or Antitheft systems

Cooling system, Water pump, What type of coolant to use